microwave & optical driver amplifiers - chip 4 4 - 2 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com gaas hemt mmic modulator driver amplifier, dc - 43 ghz v02.0209 general description features functional diagram small signal gain: 12 db output voltage: up to 8v pk-pk single-ended i/os high speed performance: 46 ghz 3 db bandwidth low power dissipation: 0.9 w small die size: 2.1 x 1.70 x 0.1 mm electrical speci cations*, t a = +25 c typical applications this hmc-auh232 is ideal for: ? 40 gb/s lithium niobate/ mach zender fiber optic modulators ? broadband gain block for test & measurement equipment ? broadband gain block for rf applications ? military & space the hmc-auh232 is a gaas mmic hemt distributed driver ampli er die which operates between dc and 43 ghz and provides a typical 3 db bandwidth of 46 ghz. the ampli er provides 12 db of small signal gain while requiring only 180 ma from a +5v supply. the hmc-auh232 exhibits very good gain and phase ripple to 40 ghz, and can output up to 8v peak-to-peak with low jitter, making it ideal for use in broadband wireless, ber optic communication and test equipment applications. the ampli er die occupies less than 3.6 mm2 which facilitates easy integration into multi-chip-modules (mcms). the hmc-auh232 requires external bias-tee as well as off-chip blocking components and bypass capacitors for the dc supply lines. a gate voltage adjust, vgg2 is provided for limited gain adjustment, while vgg1 adjusts the bias current for the device. hmc-auh232 parameter min. typ. max. units frequency range dc - 43 ghz small signal gain 0.5 - 5.0 ghz 12 14 db 35 - 45 ghz 10 12.5 db input return loss 10 db output return loss 8.5 db supply current 180 225 ma 3 db bandwidth 43 46 ghz gain ripple (5 to 35 ghz) 0.6 1 db group delay variation [1] 0.5 - 5.0 ghz 14 20 ps 5 - 30 ghz 10 11 ps 30 - 45 ghz 22 25 ps
microwave & optical driver amplifiers - chip 4 4 - 3 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz parameter min. typ. max. units 10% to 90% rise / fall time [2] 6 - 12 ps output voltage level [3] 8v p-p additive jitter (rms) 0.4 ps 1 db output gain compression point at 20 ghz 16.5 dbm output power 20 ghz @ pin= 15 dbm [4] 22 22 dbm 40 ghz @ pin= 15 dbm [4] 17 19.5 dbm power dissipation 0.9 1.25 w noise figure 5 ghz 5.4 db 10 & 15 ghz 4.2 db 20 ghz 4.6 db 25 ghz 5.4 db 30 ghz 8.3 db 35 ghz 7.4 db 40 ghz 9.1 db [1] measured with a 1 ghz aperture [4] veri ed at rf on-wafer probe. vgg1 is adjusted until the drain cur- rent is 200 ma and vgg2= 1.5 v.the drain voltage is applied through the rf output port using a bias tee with 5 volts on the bias tee. [2] measurement limited by rise/fall time of input reference signal [3] with a 2.7 v p-p input signal *unless otherwise indicated, all measurements are from probed die electrical speci cations (continued)* parameter symbol min. typ. max. units positive supply voltage v d 56v positive supply current i d 150 180 225 ma rf input power 12 16 dbm bias current adjust vgg1 -1.5 -0.2 v output voltage adjust vgg2 0 1.5 2 v operating temperature t op 02585c power dissipation p d 0.9 1.25 w recommended operating conditions parameter p diss t base t ch rmtf (w) (c) (c) (c/w) (hrs) thermal resistance to back side of chip 1.25 85 145 48 5.8 x 10 8 thermal resistance to backside of carrier using 25.4 um of 84-1lmit epoxy 1.25 85 155 56 1.8 x 10 8 thermal resistance to back side of chip 1.25 110 170 48 3.9 x 10 7 thermal resistance to backside of carrier using 25.4 um of 84-1lmit epoxy 1.25 110 180 56 1.4 x 10 7 thermal characteristics parameter symbol typ. units activation energy e a 1.7 ev median time to failure (mtf) @125 c channel temperature mtf 6 x 10 9 hours reliability characteristics
microwave & optical driver amplifiers - chip 4 4 - 4 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com input return loss vs. frequency output return loss vs. frequency gain vs. frequency noise figure vs. frequency output voltage delta vs. control voltage note: measured performance characteristics (typical per- formance at 25c) vgg2 = 1.5v, vdd= 5v, idd = 200 ma (measured data obtained from die in a test xture unless otherwise stated) 9 10 11 12 13 14 15 16 17 0 5 10 15 20 25 30 35 40 45 gain (db) frequency (ghz) -25 -20 -15 -10 -5 0 0 5 10 15 20 25 30 35 40 45 input return loss (db) frequency (ghz) 4 5 6 7 8 9 10 0 5 10 15 20 25 30 35 40 noise figure (db) frequency (ghz) -35 -30 -25 -20 -15 -10 -5 0 0 5 10 15 20 25 30 35 40 45 output return loss (db) frequency (ghz) -1.4 -1.2 -1 -0.8 -0.6 -0.4 -0.2 0 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 ouput voltage delta(vpp) vgg2 pin voltage hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz
microwave & optical driver amplifiers - chip 4 4 - 5 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com absolute maximum ratings input reference signal prbs=2 31 -1, 2.1v input, data rate of 40 gb/s note: measured performance characteristics (typical performance at 25c) (measured data obtained from die in a test xture unless otherwise stated) output reference signal prbs=2 31 -1, 7.3v input, data rate of 40 gb/s drain bias voltage (vdd) +6 vdc gain bias voltage (vgg1) -1.5 to 0 vdc output voltage adjust (vgg2) 0 to +2 vdc rf input power +18.5 dbm 40 gb/s input voltage pk-pk (vpp) 3v thermal resistance (channel to die bottom) 48 c/w channel temperature 180 c storage temperature -65 to +150 c operating temperature -55 to +110 c electrostatic sensitive device observe handling precautions hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz
microwave & optical driver amplifiers - chip 4 4 - 6 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com outline drawing notes: 1. all dimensions are in inches [mm]. 2. typical bond pad is .004 square. 3. backside metallization: gold. 4. backside metal is ground. 5. bond pad metallization: gold. 6. connection not required for unlabeled bond pads. 7. overall die size .002 die packaging information [1] standard alternate gp-1 (gel pack) [2] [1] refer to the packaging information section for die packaging dimensions. [2] for alternate packaging information contact hittite microwave corporation. hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz
microwave & optical driver amplifiers - chip 4 4 - 7 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com pad number function description interface schematic 1 res1 dc coupled 35 termination. 2vgg1 gate control for ampli er. please follow mmic ampli er biasing procedure application note. see assembly for required external components. 5vgg2 gate control for ampli er. limited gain control adjust. see assembly diagram for external components. 6 vdd & rfout rf output and dc bias (vdd) for the output stage. 3 rfin dc coupled. blocking cap is needed. 4 res2 ac coupled 50 termination. pad descriptions application circuit hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz
microwave & optical driver amplifiers - chip 4 4 - 8 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com assembly diagram note 1: drain bias (vdd) must be applied through a broadband bias tee or external bias network hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz
microwave & optical driver amplifiers - chip 4 4 - 9 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com device mounting ? 1 mil diameter wire bonds are used on vgg1 and vgg2 connections to the capacitors and 27 resistors. ? 0.5mil x 3mil ribbon bonds are used on rf connections ? capacitors and resistors on vgg1 and vgg2 are used to lter low frequency, <800mhz, rf pickup ? 35 and 50 resistors are fabricated on a 5mil alumina substrate and should be suitable for use as a high frequency termination. ? for best gain atness and group delay variation, eccosorb can be epoxied on the transmission line covering the center 3/4 of the transmission line length. eccosorb may also be placed partially across the vg1 pad and 35 resistor for improved gain atness and group delay variation. (the insertion of the transmission line he lps reduce low frequency, <10ghz, gain ripple) ? silver- lled conductive epoxy is used for die attachment (backside of the die should be grounded and the gnd pads are connected to the backside metal through vias) device operation these devices are susceptible to damage from electrostatic discharge. proper precautions should be observed during handling, assembly and test. the input to this device should be ac-coupled. to provide the typical 8vpp output voltage swing, a 2.7vpp ac-cou- pled input voltage swing is required. at this output level, the device will be in 1db to 3db of compression. device power up instructions 1. ground the device 2. bring vgg1 to -0.5v (no drain current) 3. bring vgg2 to +1.5v (no drain current) 4. bring vdd to +5v (150ma to 225ma drain current) (initially the drain current will rise sharply with a small drain voltage, but will will atten out as vdd approaches 5v) ? vgg1 may be varied between -1v and 0v to provide the desired eye crossing point percentage (i.e. 50% crosspoint) and a limited cross point control capability. ? vdd may be increased to +5.5v if required to achieve greater output voltage swing. ? vgg2 may be adjusted between +1.5v and +0.3v to vary the output voltage swing. device power down instructions 1. reverse the sequence identi ed above in steps 1 through 4. hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz
microwave & optical driver amplifiers - chip 4 4 - 10 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com mounting & bonding techniques for millimeterwave gaas mmics the die should be attached directly to the ground plane eutectically or with conductive epoxy (see hmc general handling, mounting, bonding note). 50 ohm microstrip transmission lines on 0.127mm (5 mil) thick alumina thin lm substrates are recommended for bringing rf to and from the chip (figure 1). if 0.254mm (10 mil) thick alumina thin lm substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. one way to accom- plish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (figure 2). microstrip substrates should be placed as close to the die as possible in order to minimize bond wire length. typical die-to-substrate spacing is 0.076mm to 0.152 mm (3 to 6 mils). handling precautions follow these precautions to avoid permanent damage. storage: all bare die are placed in either waffle or gel based esd protec- tive containers, and then sealed in an esd protective bag for shipment. once the sealed esd protective bag has been opened, all die should be stored in a dry nitrogen environment. cleanliness: handle the chips in a clean environment. do not attempt to clean the chip using liquid cleaning systems. static sensitivity: follow esd precautions to protect against esd strikes. transients: suppress instrument and bias supply transients while bias is applied. use shielded signal and bias cables to minimize inductive pick-up. general handling: handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. the surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or ngers. mounting the chip is back-metallized and can be die mounted with ausn eutectic preforms or with electrically conductive epoxy. the mounting surface should be clean and at. eutectic die attach: a 80/20 gold tin preform is recommended with a work surface temperature of 255 c and a tool temperature of 265 c. when hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 c. do not expose the chip to a temperature greater than 320 c for more than 20 seconds. no more than 3 seconds of scrubbing should be required for attachment. epoxy die attach: apply a minimum amount of epoxy to the mounting surface so that a thin epoxy llet is observed around the perimeter of the chip once it is placed into position. cure epoxy per the manufacturers schedule. wire bonding rf bonds made with 0.003 x 0.0005 ribbon are recommended. these bonds should be thermosonically bonded with a force of 40-60 grams. dc bonds of 0.001 (0.025 mm) diameter, thermosonically bonded, are recommended. ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. all bonds should be made with a nominal stage temperature of 150 c. a minimum amount of ultrasonic energy should be applied to achieve reliable bonds. all bonds should be as short as possible, less than 12 mils (0.31 mm). 0.102mm (0.004?) thick gaas mmic ribbon bond 0.076mm (0.003?) rf ground plane 0.127mm (0.005?) thick alumina thin film substrate figure 1. 0.102mm (0.004?) thick gaas mmic ribbon bond 0.076mm (0.003?) rf ground plane 0.150mm (0.005?) thick moly tab 0.254mm (0.010? thick alumina thin film substrate figure 2. hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz
microwave & optical driver amplifiers - chip 4 4 - 11 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com notes hmc-auh232 v02.0209 gaas hemt mmic modulator driver amplifier, dc - 43 ghz
|
